Navien Tankless Water Heater Error Codes

Navien Tankless Water Heater Error Codes
16.09.2026
46
Quick answer

Navien tankless water heaters use three-digit E-codes documented in the manufacturer’s own service and installation manuals. E003 (ignition failure) and E012 (flame loss during operation) are among the most commonly reported, while codes like E110 (exhaust blockage) and E109 (fan motor issue) point toward the venting and combustion air system rather than the burner itself.

The documented code list

Code What Navien’s documentation says it means
E003 Ignition Failure — the unit tried to light the burner and failed
E004 False Flame Detection — the flame rod reports a flame when there should not be one
E012 Flame Loss — the burner lit, then lost its flame mid-operation
E016 Overheating of the heat exchanger — exceeded safe temperature and the unit protected itself
E030 Exhaust Overheat — shuts down when flue temperature exceeds 230°F for more than 10 seconds
E047 Exhaust Thermistor Abnormality — the exhaust temperature sensor is misreading
E060 Dual Venturi Abnormality — affecting the gas/air mixing
E109 Abnormal Fan Motor Activity — the combustion fan is not behaving as commanded
E110 Exhaust Blockage — preventing proper gas venting
E762 (NPE-2 only) Vent Installation Detector — confirms the vent pipe is fully inserted (at least 2¾ inches)
E773 (NPE-2 only) Gas Type Discrepancy Warning — the gas type set during installation does not match what is connected

E003 / E004 / E012: Ignition and flame codes

These three codes all relate to the burner actually lighting and staying lit. E003 means ignition itself failed — check that the gas supply valve is fully open and that gas is reaching the unit. E004 is the opposite kind of fault: the flame sensor is reporting a flame that should not be there, pointing to the flame rod or its wiring rather than the gas supply. E012 means the burner lit successfully but then lost its flame during operation, which can point to a airflow or venting issue disrupting combustion partway through a draw.

Advertisement

E016 / E030 / E110: Overheating and exhaust blockage

  1. E016 (heat exchanger overheating)

    The unit has protected itself from exceeding a safe internal temperature — this is a safety shutdown rather than a random fault, and points toward restricted water flow or a scaled heat exchanger.

  2. E030 (exhaust overheat)

    Triggers specifically when flue temperature exceeds 230°F for more than 10 seconds — check the venting for the correct pipe diameter and length per Navien’s installation specifications.

  3. E110 (exhaust blockage)

    Check the full exhaust vent run, indoors and outdoors, for anything obstructing it — debris, nesting, or (seasonally) snow or ice at the exterior termination.

E047 / E060 / E109: Sensor and fan codes

E047 points to the exhaust thermistor itself misreading temperature rather than an actual overheat condition. E060 relates to the dual venturi that manages the gas/air mixture ratio — a component-level fault rather than something end users typically resolve themselves. E109 means the combustion fan is not responding correctly to the commands sent to it, which can stem from a wiring issue or a fan motor fault.

E762 / E773: NPE-2-specific codes

These two codes are specific to the NPE-2 model line. E762 is a vent installation safety check confirming the vent pipe is inserted the full required depth (at least 2¾ inches) before the unit will operate — worth checking after any vent work was done. E773 flags a mismatch between the gas type configured during installation (natural gas vs. propane) and what is actually connected, which needs correcting at the gas valve configuration rather than anywhere downstream.

When to call a technician

When to call a licensed technician

Gas valve configuration (E773), ignition system faults (E003/E004), and internal sensor faults (E047, E060, E109) all involve components that should only be serviced by a technician familiar with gas-fired tankless equipment. Navien support (1-800-519-8794, Monday–Friday, 5 AM–6 PM Pacific) can also help confirm whether a code needs a service call.